Crazy Weather

Today was an interesting day.  Mostly cloudy, warnings of lots of bad weather, but so far only a teeny bit of rain.  I got a lot done today.

I built the slide out shelf for a laptop and/or to place iPhones or other I suppose even a fan, heater or whatever.  

Once I had figured out the dimensions of the shelf and how I was going to mount it, I needed to figure out how I was going to get the 12 volt power ports into the cabin.  I decided not to put them behind the slide out shelf because it would have been really hard to get to them.  Instead, I put them to the right of the shelf.

Here is the housing for the power ports.

Drawer slides in place and open.

Pull out shelf installed.

Open.

Power ports installed.

The next big project was to get all the cables cleaned up and organized.  This is the battery strap which holds the battery in its place.  

 

My simple on/off switch for the battery.  Simply twist it to the right to turn it on; twist it to the left to turn it off.

Everything tidied up and strapped down.  I installed the fire extinguisher too.

Doors and all hardware installed.

The galley is complete.  The only thing I need to do is install the sliders on the cooler slide out tray.  Still need to fix and install the reading lights again and install all the additional insulation.  Not too much more inside work left though.

Baskets and Electricity

The baskets for the cabin arrived today.  I feel a little odd saying how excited I was to put them into their place.  They fit perfectly and the color is great.

I had really hoped that I could get the electrical system back in order.  I have had trouble with the super simple AC system.  Turns out it was me that was the problem, not the power cord.  I didn't realize that the red light was lit when the system was 'on.'  I was thinking that the red light on the GCFI meant that the circuit was broken.  So, all the time I thought I had some sort of problem with the GCFI, it was really just me being a doofus. 

Well, I was able to wire the Marinco port to the power cord and then into the AC outlet.  I spent several hours monkeying around with daisy chaining outlets so that I could have one inside the cabin.  In the end I decided not to do that; it just isn't worth stringing the wires into the cabin.  I'll still put the two 12 volt outlets in the cabin.  I'll have a plug in inverter in the cabin should I need it.

I installed the battery charger in the electrical compartment too.  You can just barely see the small hole I drilled into the compartment so that I can bring the plug to the battery charger.  Wasn't the way I planned on rigging it up, but it works.

Everything is coming together pretty well here.  I have a bit more 'bundling' of wires to do; I'll do that after I add the two 12 volt outlets in the cabin.

Thankfully, this is the side most people will see when they look into the galley.  I am really happy with how the 'control center' section of the teardrop has come together.

I didn't take any photos of it, but I spent quite a bit of time today working to cut the insulation pieces for the walls.  I'll cover those with headliner material and then glue them into place in the next few days.

One thing I noticed is that I can't work in the teardrop during the main part of the day.  It's just too hot to be out there on the patio in the sun.  So, it's early morning or late afternoon for me to work on the teardrop.

Frustration.

Today was less than excellent.  I met with a lot of frustration today.

It started out pretty good; I got my new fish eye lens for my iPhone and I had a lot of fun making interesting images with it.  Here you can see that I was filling the holes and then re-painting the drawers and the counter trip piece.

One of the only things that did go well today is that I was able to wire up the fuse panel and all of the electrical fixtures, even the galley light, worked perfectly.

This is 'mid-wiring.'  I like how the steel box worked out as a cover for the two 12 volt outlets.

I took the fish eye inside and I could finally capture how huge the teardrop is inside!  That was meant to be funny; but it really is pretty spacious.  Here you can see what it looks like when I am leaning up against the bulkhead; which is where you'll find me reading when it's raining out.

Here you can see the full span of the interior.  

About the only thing that did go well today was that I figured out how to get the wires from the marker lights and the LED lights on each corner, to the back of the teardrop.  I ended up being able to use the PVC pipe I had from another project.  I used insulated pipe clamps to anchor the pipe to the frame.  Pulling the wires through it was a cinch.

I need to figure out a water tight way of bringing in the marker lights and the LED leads.  I'm thinking of putting a piece of threaded conduit in the wheel well in such a way that no moisture will make its way into the electrical area.  I'm going to need to think about that some more.  

One reader, Emmett, noted that the floor is bare wood.  It's actually marine plywood that has been treated, but I am planning to take the teardrop to have an undercoating applied to it; or possibly do it myself once I compare costs.  I appreciate the head's up.  I had it on my radar, but sure do appreciate the reminder.  I'll remove the spare tire, etc. before the undercoating is applied.  

Thinking back on the day and realizing that what frustrated me so much was not having all the supplies I needed to do the job.  I had to go to the hardware store four times today for various bits and pieces.  That always frustrates me.  I also ran out of wire; another thing I obviously needed.  Oh well, this is a short week and a long weekend.  I'm hopeful that next weekend I'll be able to finish the electrical and begin insulating the cabin. 

Finally, Some Progress I Can See!

My day started bright and early.  Went for a coffee and then dug right in.  Got the rest of the galley that had not been finished painted.

My second project was finding a way to mount the spare tire under the galley.  You can see the three bolts just in front of my drill.  I used rubber washers to hopefully keep any water from penetrating through the floor of the galley.

Three of the five bolts; should be plenty of support.

Next, I painted all the drawers and doors.  I started by painting them all blue.  I immediately regretted that decision.  I waited for them to dry and then painted them brown; which was my original plan.

The next project was to cut the hole for the Marinco power port entry.  I was very anxious about cutting the hole in the side of the wall.

There's the hole.  The problem I had to solve next was how to trim the wood on the inside so I could use the washer/nut that goes on the inside.  The walls were a little too thick.  I ended up using one of my sanding cylinders; that worked perfectly.

The port installed.

What it looked like from the inside.

Next project, install the gasket over the hinge. I taped it in place to get a feel for how large the gasket would be.

The sun was hot and it ended up helping me a lot because the gasket and the butyl tape heated up and made it easy to 'stick' in the right place.

I ended up adjusting the edges of the gasket a bit.  I bent the aluminum over the edge so that any rain would run off the drip edge.

I'm really happy with how this turned out.

Cabinets, drawers and doors, take two.

Not a good photo, but you can see how I mounted one of the four LED lights that will come on when the porch lights are lit.  Hopefully this will keep me from banging my shin into the corner at night.

Was able to install the galley light.  I really like that it is on a swivel.  That way you can aim it where you need it.

Was able to put in all the power receptacles and fixtures.  They are not connected yet; that's my big goal for tomorrow.

Close up of the spare tire mount.

The last major problem I solved today was one that had been causing me a lot of trouble.  I could not get the latch on the teardrop to connect.  I also could not figure out how to make the new handle work with the old fixture.  The first part, getting it to fit ended up being easy; I just bolted it in place.  The second part, getting it to work, not so much.  Because the latch is a blind connection (you can't see what's going on because the hatch is in the way) I could not figure out how to get the 'catch' to connect.  Then I had an idea:

I needed someone small enough to fit in the cooler slot so that when I closed the hatch they could see what was happening with the latch.  Jack just so happened to come out and ask if I needed any help.  Within twenty minutes, we had it fixed!  Now, the latch is installed and works perfectly!

As I mentioned before, tomorrow's goal is to get the electric completely done.  I'm going to go set my alarm.

Electric and Other Stuff

So today was a mixture of many small projects.  I started wiring the trailer for electric.  I was a little intimidated by the idea of doing this.  I've had some negative experiences with electric in my house and have always ended up having the electricians come in and do it.  It just scares me too much.

So, today I started by testing out the various fixtures while connected to the battery.

Here are the two main interior fixtures, the dome light and the reading lights.  The first thing I had to remember is that sometimes fixtures come with different color wires.  Both of the above fixtures had white and black wires.  I just had to remember that black was hot on those fixtures.  I then connected the red wires to these terminals and all was good.  I was so happy to see both light fixtures actually light up!  Then I decided to wire the interior lights together to put them on one circuit.

The reading lights have a recessed connection, so they had to be installed onto a block of wood.  This then was screwed to a piece of hardboard, which was glued to the foam.  It all should work out smoothly for me when it comes time to cover it with the headliner.  I'm hopeful that I can put that section on in one large piece.

Here you can see how I braced the foam to the roof.  Using these planks of wood worked pretty well.  I used Gorilla Glue for the first time.  That stuff is interesting.  It's kind of like working with the extruded foam; it actually looks like that when it dries.  It also 'expands,' which regular glue does not do in the same way.

Here you can see the small pieces of hardwood that are glued to the foam.  This gave me something to 'screw' into for each fixture.

Here are the fixtures mounted onto the hardboard and foam.  You can see the channels I cut for the wires.

You can see the hole coming in from the cabin.  I just got plain lucky that the shelf in the cabin was at the same height of the counter top in the galley.  I was able to tuck the wires into the power center area very easily.

This is the hole going into the power center.

You can see how the fuse panel will fit into the side wall there.

Here you can see the two 12 volt power port holes and the small square hole is where the 12 volt battery meter will be placed.  I decided to use two steel boxes.  One will potect the back side of the 12 volt outlets and the other will be for the one 120 volt outlet that I will install after I put the power port entry hole on the outside of the teardrop.

Another big task was putting the original hinge back on.  You can see on the image above that I used the butyl tape to seal the top part of the hinge.  I then screwed into a 1" by 1".  This gave the hinge something to 'bite' into and I think allowed me to really tighten the hinge.

These clamps worked well to hold everything where I wanted it while I was screwing it in place.

Here is the 'porch light.'  These will be tied into the four small LED lights, one on each corner too. 

They will all come to a central switch on the shelf area.  I can't wait to see how these are going to look at night!

Everything worked!  I shouldn't have been surprised, but given my history with electricity, I was!  I had not had the chance to 'sit up' and use the reading lights before.  I found that leaning against the bulkhead, which is headliner covered foam, was very comfortable and the lights will work perfectly!

I thought I had done something wrong with the vent.  I couldn't get it to turn on.  Then I realized that you have to have the vent hood open for it to turn on.  It is quiet and truly moves a ton of air around.  It isn't too noisy, but just noisy enough to work for us as a white noise creator.

I also was able to fix up the drawers and doors.  I had done a poor job on their fronts.  I routed the edges of the doors and sanded their fronts properly.  

One of the last projects was installing the new screw/bolts that hold the struts in place.  These struts hold up the hatch.  It was amazing to me how much a small bag of stainless steel hardware can cost.  

Tomorrow I have to get the second half of the hinge installed and the vent and doors sealed up so that the teardrop can go out onto the concrete patio.