Hot Day!

The temperature outside the teardrop on the patio was 102 degrees (in the shade) and the temperature inside the teardrop was 97 degrees.  I really don't like hot weather; especially when I want to work outside.  I cannot imagine how the guys who work on the roof or on the roads do it.  I took lots of breaks, drank lots of cold water, and moved my zero gravity chair into the garage to cool down.

Not a lot of photos to document my work today.  

I made the hardware for the window curtain rods and painted them glossy black.

I carved the foam pieces for the bulkhead.  Covered them in foam and then installed them.  Turns out the glue (PL 300) did not work well on the insulation (1/2") that I used on the bulkhead.  I didn't think that very thin plastic layer on top of the insulation would be a problem, but the glue only 'stuck' to it, not the actual insulation.  So, I needed to pull out four of the strips of cedar and re-glue them.  I ended up using Gorilla Glue.  I also used a little bit of it on the foam covered pieces along the wall of the bulkhead.

Used the marine grade contact cement and clamps to glue the foam door panels to the door.  They turned out fantastically!

Very carefully created a pattern for the cut out for the mattress.

Traced the pattern onto the foam mattress.  Used a $14 electric knife to cut the two small wheel well sections out; ended up with two really nice pieces of foam that I may turn into a back rest or possibly a couple of pillows for the teardrop.  Couldn't believe how easily I could cut the foam.  Two minutes and it was done.  The mattress pads fit right over the cut outs; we may not even need to customize the covers. 

Not quite as productive a day as I would have liked, but all in all it was successful.  Tomorrow is the day to start working on polishing the body.  Not sure what new experiences that will bring for me!

Gorgeous Day!

Today was magnificent!  I love the weather when it is 70 degrees and sunny.  I embraced the sun today and set up my work table on the patio in the glorious sun.  Okay, to be truthful, I slept in late and by the time I got outside the sun had crested and the sun was only partly on the patio.

A perfectly blue sky; the moon is hiding directly in the middle.

My big challenge today was to install the rest of the insulation and finalize the interior electric.  Mission accomplished on both parts.

In this image you can see the switch for the porch lights in place.  I'm going to need to do a little finesse work to install it.  Notice how nice the insulation and headliner look in the corner there.  I will finish the back wall by installing the cedar strips.

You can see in this image that I installed a strip of cedar right next to the door.  This was a cool thing I thought of because I needed something solid to anchor into for the cup holders.  I used 3/4" foam insulation instead of the 1" that I had been using.  With the cedar strip glued to it with Gorilla Glue, it came out to be the same thickness as the covered foam.  Once it has completely set up, I'll install the drink holders.  You can also see in this image how I used the foam to form 'panels' that were then covered with the headliner material.  I actually didn't have to glue them into place.  They are held in place by friction.  The small bolts that hold the door frame in place are all that was needed to hold the panels tightly in place.

After cutting the panels, I used Loctite 300; it is specially formulated for Marine applications and high heat.

Heavy coats on both the fabric and the foam.  Again, this adhesive was formulated to work on foam.  Normal adhesive would 'eat' away the foam.

This stuff had exceptional tack.  It was simple once the fabric was cut and sprayed to make the panels.

Here they are ready to install.

The great thing about doing it this way is that if I ever 'did' need to remove a panel, It would not be difficult to do so.  It is also very simple if I ever need to install any type of hardware on the outside of the teardop, I can simply pull out a panel and attach the hardware; then simply pop the panel back in place.  I am going to put a piece of cove molding along the entire 'seam' between the cedar and the insulation panels.  I tested it out today and it is a 1" cove molding that will bend perfectly.  This additional friction will hold things neatly and give a really nice finished look.

 

The reading lights look really great I think.  I like the accent color and the way the silver looks against the brown.

 The power port worked great today to charge my phone while I was in the teardrop working.  

Tomorrow I will need to figure out what I will do with the bulkhead area.  Part of me would really like to have the cedar strips and insulation in there.  The other part of me worries that if I insulate it I will take away valuable 'space.'  Not really sure what will go in there.  Probably shoes, jackets, rain gear; maybe even fishing poles?  I'm sure my wife will have some good insight on what to do there.

The teardrop this evening as I was finally cleaning up at 9:00 p.m.  It was a good eleven hour work day!